MATLAB with RTL SDR and Xilinx FPGA devices

-
Just like GNU Radio in Linux, MATLAB could be used for RF decoding and analysis with RTL SDR as source. Communication tool box in MATLAB has option to add RTL-SDR support to MATLAB.
Similarly MATLAB also supports Xilinx FPGAs to be used as hardware platforms for users to develop algorithms in system block level , and hence hiding many low level design design hurdles during fpga development of the same.
MATLAB can work together with Xilinx System Generator for this purpose. Many DSP functions are available as xilinx blocks in MATLAB-Simulink Library
http://in.mathworks.com/hardware-support/rtl-sdr.html

Comments

Unknown said…
Have you made any progress on this idea yet?
May 6, 2015 at 1:57 AM
Antony said…
got hooked up with something else now...
November 12, 2015 at 11:13 PM
Post a Comment

Popular posts from this blog

DIY Fixing a Laptop Battery

-
Image
Hi Friends ,  DIY is always fun and awesome, and so welcome to another word of tech byte... This note is a collective scratchpad of troubleshoot methods and fixes i came across recently for fixing my laptop battery that went bad. Battery Model   : HP HS04  battery pack (4 cell , lithium ion, 14.6V , 2670 mAh, 41 Wh) Laptop  Model  : HP 15-ac635tu   (equivalent to HP G4 250 Notebook) The Symptoms Laptop Showed 1. Laptop charger goes on and off intermittently after charging up to more than 60% . The charger port LED goes between charging and not-charging frequently. 2. Once laptop is running from battery, charge percentage drops faster than normal, and once it reaches 23% , laptop shuts off immediately. On power in on again the charge percentage will be less than 15% and wont complete bootup to desktop. Faints instantly. Troubleshooting 1. Borrowed a laptop charger from my friend and tried 2 or 3 charge cycles. But still the issue...
Read more

Bidirectional 3.3v 5v Level Shifter

-
Image
Hi guys.. welcome to another simple DIY project... Lets make a level shifter, which will just shift a 5v data line to 3.3v or vice versa... Okie why we need such a shifter..  ? or what is this stuff actually.... ? We run around huge bunch of devices that run in various voltage levels.. for example Raspberry Pi runs in 3.3v, and its all GPIO I/O pins are at this level, even though we provide a 5v USB input. And so it is not tolerent to 5V input levels from another device or sensor modules connected to it over I/O pins using SPI, UART, i2C... whatever.... Another example is Arduino UNO which runs in 5V, normally is driving all its I/O at 5V levels.  So interfacing boards at different I/O voltage levels requires a level shifter. Simple voltage divider circuits can help for an extent.. but they dont provide low voltage  device protection or bidirectional shifting. Wait a minute ... Bidirectional... what is it ? Okie.. some communication protocols like i2C are b...
Read more

Introducing an FPGA-ARM Dev Kit for Embedded Linux Starters- Avent MiniZED Board

-
Image
Hi All ,  Welcome to another tech byte.... Embedded Linux is a very powerful area in the current age of IoT  and Edge Computing. But as an FPGA RTL person throughout the career , i had  numerous situations where had to work side by side with embedded software engineers who were  linux gurus. I have seen their struggle starting from setting up environment for development, building code , solving hardware dependencies , integrating software pieces for limited resources , cross compiling , optimising for performance so and so... Rather than few sneek peaks into their works, i have never dared myself to do a hands on into these linux stuffs.. I was pretty happy with few diagnositc linux commands which told me , yes data to and from my FPGA side is pretty solid and running.. And we had run into situations where we play "ball in your court" game  when a bug pops up from nowhere.. We blame it on software and they shout it back on RTL  :) But last project ...
Read more